Discussion and support for MoTeC Power Distribution Modules
-
- Controlling rad fan w/ PDM15 and M400
by eric_s on Sun Dec 29, 2013 4:46 am
- 10 Replies
- 32962 Views
- Last post by mstech
on Wed Jul 09, 2014 3:32 pm
-
- Setup Config Loom PDM 15
by TKManx on Wed May 14, 2014 2:57 pm
- 2 Replies
- 9649 Views
- Last post by TKManx
on Sat May 17, 2014 10:13 am
-
- Racegrade Keypad CAN IDs
by Robin Poenisch on Wed Jul 31, 2013 10:58 pm
- 15 Replies
- 41073 Views
- Last post by chelspeed
on Wed Mar 12, 2014 3:57 am
-
- PDM output spikes
by Fast_Moto on Thu Feb 27, 2014 5:12 am
- 3 Replies
- 11913 Views
- Last post by Scott@FP
on Sat Mar 01, 2014 8:39 am
-
- Firmware problems
by doriansinger on Thu Feb 27, 2014 5:31 am
- 1 Replies
- 7934 Views
- Last post by mstech
on Thu Feb 27, 2014 8:37 am
-
- PDM15 Current Reading Calibration
by eric_s on Sun Dec 29, 2013 12:13 pm
- 4 Replies
- 13831 Views
- Last post by Holmz
on Wed Jan 01, 2014 10:21 am
-
- Controll PDM
by plosey on Thu Mar 21, 2013 9:37 am
- 0 Replies
- 6747 Views
- Last post by plosey
on Thu Mar 21, 2013 9:37 am
-
- Voltage Outputs
by plosey on Tue Dec 04, 2012 5:17 pm
- 1 Replies
- 7528 Views
- Last post by Martin
on Fri Jan 18, 2013 4:46 am
-
- Light Flash
by plosey on Tue Dec 04, 2012 5:19 pm
- 1 Replies
- 8408 Views
- Last post by MattW
on Wed Dec 05, 2012 9:17 am
-
- Toggle Default ON
by plosey on Sat Nov 10, 2012 6:47 am
- 3 Replies
- 12270 Views
- Last post by Herrubermensch
on Sat Nov 17, 2012 12:11 pm
-
- PDM15 Inputs: Internal Resistance?
by Jakob on Sun Nov 04, 2012 5:03 am
- 1 Replies
- 7221 Views
- Last post by YuriK
on Thu Nov 15, 2012 12:02 pm
-
- PDM30 Firmware update trouble
by plosey on Fri Oct 19, 2012 2:34 am
- 2 Replies
- 9832 Views
- Last post by plosey
on Sat Oct 20, 2012 2:45 am
-
- Unused channel reports 142% load
by JayDee on Sat Sep 15, 2012 6:33 am
- 1 Replies
- 7251 Views
- Last post by YuriK
on Wed Sep 26, 2012 12:27 pm
-
- Messages with unknown CAN IDs sent by PDM
by lokmanho on Wed Jul 18, 2012 8:33 pm
- 3 Replies
- 12163 Views
- Last post by JayDee
on Tue Jul 31, 2012 12:15 am
-
- Keep existing output values when entering Test Output mode
by lokmanho on Fri Jul 20, 2012 2:12 am
- 0 Replies
- 6105 Views
- Last post by lokmanho
on Fri Jul 20, 2012 2:12 am
-
- Multiple PDMs Controlled by Same Motec Switchpad via CAN
by Herrubermensch on Thu May 10, 2012 3:36 pm
- 2 Replies
- 10029 Views
- Last post by Herrubermensch
on Sun Jul 01, 2012 4:23 am
-
- CAN output, confirm blank field = no message
by phatbob on Wed Jun 27, 2012 6:14 am
- 2 Replies
- 8515 Views
- Last post by YuriK
on Fri Jun 29, 2012 5:57 pm
-
- PDM load limit and expected behaviour
by phatbob on Wed Jun 27, 2012 6:18 am
- 1 Replies
- 6964 Views
- Last post by JamieA
on Thu Jun 28, 2012 11:34 am
-
- CAN messages into PDM
by pcarroll on Sat Mar 31, 2012 8:32 am
- 13 Replies
- 37102 Views
- Last post by JamieA
on Wed May 30, 2012 2:37 pm
-
- Initial power up cycling outputs
by pcarroll on Mon Apr 09, 2012 6:04 am
- 0 Replies
- 5975 Views
- Last post by pcarroll
on Mon Apr 09, 2012 6:04 am
-
- Wiper Control with PDM
by incontrolsteve on Sun Nov 13, 2011 8:29 am
- 2 Replies
- 10403 Views
- Last post by pcarroll
on Mon Apr 09, 2012 5:59 am
-
- PDM15 data to SDL3 to Shift Module
by rayhall on Thu Mar 15, 2012 10:30 am
- 1 Replies
- 7420 Views
- Last post by JamieA
on Wed Mar 21, 2012 11:39 am
-
- PDM32 Programming Loom
by rdmahurin on Wed Mar 23, 2011 6:31 am
- 3 Replies
- 11613 Views
- Last post by JamieA
on Tue Feb 21, 2012 4:31 pm
-
- PDM to Replace Fuse Box in Engine Bay
by HKS_TRD on Tue Jan 17, 2012 11:01 pm
- 3 Replies
- 15442 Views
- Last post by Holmz
on Fri Jan 20, 2012 6:39 pm
-
- Combine Outputs
by Jakob on Mon Jan 16, 2012 11:01 am
- 1 Replies
- 7225 Views
- Last post by JamieA
on Tue Jan 17, 2012 11:24 am
Return to Board index
Users browsing this forum: No registered users and 6 guests
Forum permissions
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum